Series TSr (Modular)
- NEMA 4X Fiberglass Enclosure
- Individual, Replaceable Modules
- 50 – 300kA per Mode Models
- TSrc Commercial Series (TpMOV & Filter Capacitors)
- TSri Industrial Series (adds Silicon Avalanche Diodes)
- Optional Surge Counter/Audible Alarm
- Optional Form C Contactand/or Phase Loss Contact
- Optional Extended Filter Network (EFN)
- Optional Multi-Function Relay (MFR)
- UL1449 5th Edition / UL1283 7th Edition Listed
Downloads
Need help configuring models and options?
Give us a call 804-355-1100
Design
Low Impedance Surge Paths
- Yellow zinc plated, low carbon steel back pan
- ¼” thick x ½” wide C11000 Copper Bus Bar
- #6AWG, Rope-Lay internal Power Wiring
Replaceable Modules
- Individual, Replaceable Module
- Secures to Buss Bars with ¼” hardware
- LED indication on Each Module
Hybrid Suppression Technology
- TSrc (Commercial Series) – 2-Tier Design
- TSri (Industrial Series) – 3-Tier Design
Surge Component Technology
Thermally Protected, Metal Oxide Varistor (TpMOV)
- ANSI/UL 1449 4th Edition, Type 1 Component
- Fail-Safe Design
- 50kA 8x20us Rated
- Visual Fail indicator as well as a normally open micro-switch
- Applied L-N, L-G & N-G
EMI / RFI Filter Capacitors
- X2 SMPS EMI Suppression Capacitors
- 1uf, 305Vac Rated
- Applied L-N &/or L-G
TVS Diodes / Silicone Avalanche Diodes (SADs)
- UL 497B Recognized
- Provide Faster Response Time
- 1.5kW or 15kW Sizes
Input Termination
Terminal Blocks (Standard)
Slotted Screw Terminal Blocks that accept up to a #4AWG. Copper Conductor
Distribution Blocks (Optional)
Slotted Screw Terminal Blocks that accept up to a #2AWG. Copper Conductor
Fused Disconnect (Optional)
Integral, Fused Disconnected Switch that accept up to a #4AWG. Copper Conductor
Monitoring
Form C “Dry” Contacts (Standard)
- Every TSr comes standard with (2) Form C, “Dry” Contacts that change state on an SPD Module failure
- Optional Phase Loss “Dry” Contacts available that changes state on any loss of phase
MODULE LEDs (Standard on all TSr’s)
- Each Suppression Module contains a Green (Module Good) and Red (Module Failed) LED
- Each Module is Keyed & color coded to prevent installing a wrong replaceable module
- ¼-20 Serrated Hex Nuts secures Module in Place
- Each Module wired back to Power Supply for Status control
SURGE COUNTER and/or AUDIBLE ALARM (Optional)
- Module LEDs & Dual Form C Contacts, PLUS;
- Audible Alarm with Silence Button;
- Surge Counter with (8) sensitivity settings;
- Status LED’s
- Monitor Power On / Off Button
- Horn Disable option
Additional Options
EXTENDED FILTER NETWORK (Optional)
Provides additional EMI/RFI electrical noise attenuation up to 53dB in the range of 50kHz to 100MHz as defined by MIL-STD-220A test procedures.
MULTI-FUNCTION RELAY (Optional)
Provides Output Contact for status of Over / Under Voltage within a Range, Phase Loss, Phase Rotation & Phase Balance
POWER QUALITY MONITOR (Optional)
- Total Harmonics Distortion (THD)
- Waveform Capture
- Onboard Ethernet
- Data & Event Logging
- Current Transformers
- [Optional] Environmental Monitoring
Enclosures
FIBERGLASS ENCLOSURE (Standard)
- Made from hot compression molded halogen free, self extinguishing fiberglass reinforced polyester (FRP)
- 1/4” transparent Lexan™ window
- Protection Rating: NEMA Type 3; NEMA Type 3R; NEMA Type 4; NEMA Type 4X; NEMA Type 12; NEMA Type 13; IP66 16” H x 14” W x 8” D
or 18” H x 16” W x 10” D
STAINLESS STEEL ENCLOSURE (Optional)
- Type 304 Stainless Steel with #4 Brushed Finish
- Protection Rating: NEMA Type 3; NEMA Type 3R; NEMA Type 4; NEMA Type 4X; NEMA Type 12; NEMA Type 13; IP66 20” H x 16” W x 8” D
POWER QUALITY MONITOR SYSTEM (Optional)
- Incorporates (2) Fiberglass enclosures on a stainless steel back pan
- Protection Rating: NEMA Type 3; NEMA Type 3R; NEMA Type 4; NEMA Type 4X; NEMA Type 12; NEMA Type 13; IP66 48” H x 24” W x 8.50” D